基于街景地图数据的北京市东城区 街道绿色空间正义评估研究

绿色空间正义是城市空间正义的典型代表，意为在人群中公平分配维护绿色空间的责任和享有绿色空间的权益。根据其定义，以北京市东城区为例，从责任和权益2个角度着眼，一方面基于百度街景地图数据提炼街道空间绿视率的空间分布特点，表征街道绿色空间的客观可感知水平；另一方面将街道绿视率和实时人口热力叠加，探讨街道绿色空间的实际被感知程度，从而完成对北京市东城区街道绿色空间维护和享有情况的评估。发现邻近使用者维护街道绿色空间的责任对绿化客观可感知水平的重要性，以及合理的道路断面设计对同时提升街道空间活力和绿视率即绿化实际被感知程度的有效性。由此总结出2点街道绿色空间规划设计建议，即明晰权责边界并保证公共权益优先级，以及加强落地性设计导则中对绿色空间正义问题的关注，并对未来研究提出展望。     

因素空间理论下基点分类算法研究

目前，基于因素空间理论的背景基提取算法计算过程复杂，初始化必须依赖各因素极值，基点数量提取冗余等原因，未能在应用中取得很好效果。为此，结合内点判别法和知识可继承、可扩展的思想，提出一种计算简单、初始化独立、基点数量小的改进的背景基提取算法。然后，利用改进的背景基提取算法构造出一种全新的数据分类算法-基点分类算法，基点分类算法以提取每一类样本的背景基为预测模型，再通过新定义的λ-背景基，优化预测模型。数值实验表明:基点分类算法原理简单、构造难度小、分类模型泛化能力强，预测能力准确率高，同时严格的模型限定区域又能为识别新类别提供新方法。     

影响干式磁选机在石英除铁过程中的因素研究

本文通过对陕西某地石英矿进行干式磁选试验研究,介绍了给料速度、尾矿抛尾率、矿样含水率及含泥量等几个因素对干式磁选作用的影响,分析了干式磁选各因素在石英除铁过程中的规律,为后续工业应用提供一定的理论基础。     

不同镀层结构钢的耐盐雾腐蚀性能比较

通过盐雾试验模拟潮湿环境,对裸钢试片、电镀锌钢试片、化学镀镍-磷钢试片和化学镀镍-钴-磷钢试片进行了宏观形貌、微观形貌和腐蚀产物成分分析,比较了四个试片的耐盐雾腐蚀性能。结果表明:在盐雾环境中,四个试片均会发生电化学腐蚀,生成不同的腐蚀产物;在盐雾腐蚀周期内,裸钢试片的腐蚀速率最高,化学镀镍-磷钢试片和化学镀镍-钴-磷钢试片的腐蚀速率较低;四个试片在腐蚀过程中的阳极反应和阴极反应不同,腐蚀后的微观形貌存在明显差异。     

高固气比技术在2 500 t/d水泥熟料线的改造案例介绍*

采用高固气比悬浮预热分解技术对宝江2 500 t/d生产线烧成系统进行技改后,预热系统出口温度从351℃降低至279℃,粉尘浓度(标况下,以下同)从151.6 g/m3减少至43.9 g/m3,系统分离效率大幅提高;入窑生料分解率从90.5%提高至98%,生产线熟料烧成煤耗从119.4kg/t降低至100.80kg/t,熟料产量从2744t/d提高至3840t/d,各指标均属领先水平。     

Comparison study of thermochemical waste-heat recuperation by steam reforming of liquid biofuels

The concept of thermochemical exhaust heat recuperation by steam reforming of biofuels is considered. Thermochemical recuperation can be considered as an on-board hydrogen production technology. A schematic diagram of a fuel-consuming equipment with thermochemical heat recuperation is described. The thermodynamic analysis of the thermochemical recuperation systems was performed to determine the efficiency of using various fuels, in particular, methanol, ethanol, n-butanol, and glycerol. The thermodynamic analysis was performed by Gibbs free energy minimization method and implemented using the Aspen Hysys program. The thermodynamic analysis was performed for a wide temperature range from 400 to 900 K, for steam-to-fuel of 1, and pressures of 1 bar. The maximum fuel conversion reaches for the following temperatures: methanol - 600 K, ethanol - 730 K, n-butanol - 860 K, glycerol - 890 K. The dependence of the reforming enthalpy on temperature is determined. It was shown that the reaction enthalpy determines the heat transformation coefficient, which shows the ratio of the low heat value of synthetic fuel and the low heat value of the initial fuel. For all studied fuels, the maximum value of the transformation coefficient is observed for steam reforming of ethanol and the maximum heat transformation coefficient is 1.187. The temperature range is determined at which the maximum efficiency of the use of thermochemical recuperation occurs due to the reforming of biofuels. For methanol, the effective temperature is about 600 K, for ethanol is about 700 K, for n-butanol is 850 K, for glycerol is more than 900 K. The results obtained make it possible to efficiently select the type of fuel for thermochemical recuperation due to steam reforming.     

煤田地震勘探中多井组合爆炸法浅析

地震勘探中炸药作为激发震源的激发条件多样,采用有效的震源激发方式,才能取得高信噪比的地震原始数据。本文依据有关爆破原理,理论结合实践经验,提出在厚黄土区采用多井组合的激发方式,能有效压制噪声,增强性噪比,提高数据质量。     

福建某低品位金矿新型浸金剂浸金试验

福建某斑岩型金矿品位低、规模大,金主要以自然金形式存在,可见金的粒度较粗,为高效利用该低品位金矿,开展新型浸金剂金蝉全泥浸出试验和柱浸试验,结果表明：全泥浸出在磨矿细度为-0.074 mm占80%、矿浆浓度25%、加石灰调pH 值11.0左右、初始金蝉浓度为500 mg/L和过程中控制金蝉浓度不小于300 mg/L条件下浸出20 h,金的浸出率为93.43%,金蝉耗量为1.02 kg/t；柱浸在矿石粒度为-30 mm条件下喷淋浸出23天,金累计浸出率和金蝉累计耗量分别为86.54%和1.22 kg/t。     

Predicting the damage development in epoxy resins using an anisotropic damage model

For fiber-reinforced plastics, the strain-rate dependent response is governed by the matrix behavior. In this work, the Goldberg model is considered for the epoxy matrix constitutive material model. Moreover, the strain-rate dependency is achieved by direct influence on the elastic modulus, the inelastic strain, and the material strain to failure. In addition, an anisotropic damage response is implemented and extended through a strain-rate dependent definition. Since the constitutive model relies on nonphysical parameters, a parameter study is further performed. Additional numerical investigations using a micro-mechanical model are performed. Tension and shear loading conditions are evaluated and the influence of different strain rates is explored. Furthermore, the implemented anisotropic damage model is compared and discussed against an isotropic damage model.     

地浸铀矿山浸出速度的影响因素

在地浸铀矿山生产过程中,铀的浸出速度是制约生产的重要参数,直接关系到矿山的服务年限。矿山生产采区往往存在严重的拖尾现象,为提高地浸铀矿山资源利用率,降低生产成本,研究了影响铀浸出速度的因素,提出了控制铀浸出速度的措施。